无线电爱好网

 找回密码
 注册

QQ登录

只需一步,快速开始

用百度帐号登录

只需两步,快速登录

使用新浪微博登录

一号多站,快速登录

人人连接登陆

无需注册,直接登录

搜索
欢迎光临无线电爱好网  www.86x.net 捍卫钓鱼岛 抵制日货
无线电爱好网 欢迎广大电子爱好者和无线电爱好者 建立自己的专业群组!最
无线电爱好网开通网络电视功能插件,有些浏览器不能正常观看,推荐使用 360极速浏览器 36
手机天线原理和设计 4411
移动通信基站基础知识 4410
周海婴被公众提及最多的一个身份是“鲁迅独子”,其实他并没有走父亲的文学之路,而是在无线电
火腿入门必读 注:资料来自网络,原作者不详 第
.李建清.扫描版3730 3731
.李建清.扫描版 3728 3729
功率放大模块.型号 频率 功率 注:资料来自网络
本帖最后由 lfcx 于 2012-8-11 15:48 编辑 http://www.86x.net/data/attachment/portal/201208/11/085633h
.李建清.扫描版.pdf 3745 3746
.刘建清.扫描版 3736 3737
基于微盟ME8204 应用 12V-2A 开关电源应用方案(原理图,PCB 下载条件
本方案使用微盟 me8204 IC 4
六级能效标准的挑战 资源:115网盘附件下
 路灯电缆故障测试仪,实际上可以由便携式测距
ARM体系结构(1).pdf 4058
嵌入式系统设计师考试笔记(完整整理版).pdf 4057
求led点阵时钟程序,急!
买仪器就到我爱仪器网,那里更全,服务更好
本帖最后由 lfcx 于 2012-1-25 18:04 编辑 资源:115
本帖最后由 lfcx 于 2012-1-6 16:31 编辑 资源:115网盘附件下载:第11讲.rar (1
资源:115网盘附件下载:MCS-51单片机原理及接口技术.rar (5.51MB)
资源:115网盘附件下载:8098单片机原理与应用.rar (4
资源:115网盘附件下载:keil+uvision4破解版下
资源:115网盘附件下载:Proteus-自建元件库.doc (563.00KB) 《单片机模拟仿真软件》Proteus7.5sp3破解汉化
μCOS-Ⅱ Mega128 源代码
Linux基础教程!!
综合台湾媒体报道,台空军屏东联队第20电子战大队破获共谍案,少校郝志雄涉嫌被大陆收
本帖最后由 lfcx 于 2012-3-23 21:22 编辑 资源:115网盘附件下载:EMC
资源:115网盘附件下载:EMC设计整改指导
这里将免费提供场地,收录国内
无线电爱好网 首页 技术应用 模拟技术 查看内容

对高阻抗缓冲放大器的输入实现ESD保护

2012-9-21 16:12| 发布者: lfcx| 查看: 750| 评论: 0

摘要:   二极管和保护装置抑制瞬时高压静电放电。   在某些测量应用中,如pH值(酸度)和生物电势需要高阻抗缓冲放大器。虽然有几个半导体制造商提供具有低偏置和输入偏置电流特点的放大器芯片,配上传感器电缆可能会 ...

 

  二极管和保护装置抑制瞬时高压静电放电

  在某些测量应用中,如pH值(酸度)和生物电势需要高阻抗缓冲放大器。虽然有几个半导体制造商提供具有低偏置和输入偏置电流特点的放大器芯片,配上传感器电缆可能会因为ESD(静电放电)对放大电路造成损害。图1显示一种不令人满意的方法实现ESD保护。电阻R1抑制ESD的放电电流,而二极管D1A 和D1B钳住放大器IC1的输入到供电电源轨。不幸的是,当并联pH值传感器的为400MΩ输入阻抗时,即使采用低漏电流二极管,如Fairchild公司的MMBD-1503A,仍引入很大的偏置电压。

一种不令人满意的方法实现ESD保护

  图2中的电路提供另一个方法。Analog Devices公司的低输入偏置,低偏置电流的AD8603放大器IC1,作为单位增益输入缓冲器。对于任何正常输入,电路的输出电压VOUT 等于其输入电压VIN。因此,电压经过ESD保护二极管D1A 和D1B接近0V,二极管漏电流均不影响传感器输出信号。依靠ESD适用电路输入连接器的极性,其高电压放电通过二极管D1A 或D1B进入供电正向或负向电源。电容C1充当中间“电荷存储器”,放慢ESD的上升速率,保护IC1的输出过程,从锁存到二极管D1A 或D1B开始分离ESD瞬流到正向或负向电源。实际上,C1补偿D1寄生电容。电阻R3允许IC1来驱动电容负载,使C1不会进入振荡状态。

另一个实现ESD的保护方法

  在ESD事件中,D1和D2可以进行传导,但通过两个前置偏移二极管压降,VIN端的电压超出供电电源电压。电阻R1和R2限制放大器输入电流在制造商建议的最大5mA之下。

  封装电路时,需要特别注意电路板的布局。电路板介电性能的缺陷会给寄生漏电流提供路径。在电路板的两面敷铜形成保护环,可以在电路高阻抗节点周围转移漏电流(图3)。

在电路板的两面敷铜形成保护环

  英文原文:

  High-impedance buffer amplifier's input includes ESD protection

  Diodes and guard traces suppress high-voltage static-discharge transients.

  Eugene Palatnik, Waukesha, WI; Edited by Brad Thompson and Fran Granville -- EDN, 9/28/2006

  Certain measurement applications, such as for pH (acidity) and bio-potentials, require a high-impedance buffer amplifier. Although several semiconductor manufacturers offer amplifier ICs featuring low bias and offset-input currents, attaching a sensor cable to an amplifier circuit can inflict damage from ESD (electrostatic discharge). Figure 1 shows one unsatisfactory approach to ESD protection. Resistor R1 limits an ESD event's discharge current, and diodes D1A and D1B clamp amplifier IC1's input to its power-supply rails. Unfortunately, when shunting a pH sensor's 400-MΩ input impedance, even low-leakage diodes, such as Fairchild Semiconductor's MMBD-1503A, introduce significant offset voltages.

  The circuit in Figure 2 offers an alternative approach. An Analog Devices low-input-bias, low-offset-current AD8603 amplifier, IC1, serves as a unity-gain input buffer. For any normal input, the circuit's output voltage, VOUT, equals its input voltage, VIN. Thus, the voltage across ESD-protection diode D1A or D1B approaches 0V, and neither diode's leakage current affects the sensor's output signal. Depending on the polarity of an ESD event you apply to the circuit's input connector, its high-voltage spike discharges through diode D1A or D1B into the positive or the negative power-supply rail. Capacitor C1 acts as an intermediate "charge reservoir" that slows the ESD spike's rate of rise and protects IC1's output stage from latching until diode D2A or D2B begins diversio

n of the ESD transient into the positive or the negative supply rail. In effect, C1 compensates for D1's parasitic capacitance. Resistor R3 allows IC1 to drive the capacitive load that C1 presents without going into oscillation.

  During an ESD event, both D1 and D2 can conduct, but the voltage at VIN exceeds the power-supply-rail voltage by only two forward-biased diode voltage drops. Resistors R1 and R2 limit the amplifier input's currents below the manufacturer's recommended 5-mA maximum rating.

  When packaging the circuit, pay special attention to the pc board's layout. Imperfections in the board's dielectric properties can provide parasitic-leakage-current paths. Adding copper traces on both sides of the board to form guard rings around the circuit's high-impedance nodes diverts leakage currents (Figure 3).


鲜花

握手

雷人

路过

鸡蛋

QQ|关于本站|小黑屋|Archiver|手机版|无线电爱好网 ( 沪ICP备13030311号-1|申请链接 |人工智能  网站事务:点击这里给我发消息 技术支持:点击这里给我发消息 广告联系:点击这里给我发消息

GMT+8, 2013-12-6 08:58 , Processed in 0.108282 second(s), 43 queries .

Powered by Discuz! X3 Licensed

© 2001-2013 Comsenz Inc.

返回顶部